Descrizione

In the Linux kernel, the following vulnerability has been resolved: wifi: rtw88: usb: route bmc frames via the high queue only for DTIM delivery In AP mode every broadcast and multicast data frame is routed to TX_DESC_QSEL_HIGH, the after-DTIM queue, whether or not anybody is asleep. The firmware drains that queue at beacon pace, a dozen or so frames per second measured on RTL8822BU, while one associated client's mDNS/SSDP chatter alone exceeds that. The excess accumulates inside the chip until the shared TX page pool is exhausted (measured: 14 of 1803 pages left). From that point every host-sourced frame queues behind the backlog: authentication responses reach the air seconds after the client has given up, so no station can associate anymore, and the beacon reserved-page download fails the BCN_VALID poll ("error beacon valid") because it needs pages from the same pool. The AP keeps beaconing, so the failure looks like a silent RX stall and only a reboot recovers. mac80211 already decides when after-DTIM delivery is needed: it sets IEEE80211_TX_CTL_SEND_AFTER_DTIM on bmc frames only while at least one station is actually dozing. Honor that instead of routing unconditionally: flagged frames keep going through the high queue with the MORE_DATA and HGQMD handling introduced by commit 076f786a0ae1 ("wifi: rtw88: Fix AP mode incorrect DTIM behavior"), everything else leaves at line rate through the AC queues. This partially reverts the usb.c hunk of that commit, whose unconditional routing is what lets the backlog build up. On a bench AP (USB2, 20 MHz, WPA2, hostapd, a Windows client driven through disconnect/reconnect cycles): reconnects fail 0/5 on RTL8822BU and 0/3 on RTL8821CU before this change, and pass 10/10 and 5/5 with it, with the page pool staying healthy and no beacon errors logged.

Testo originale del record CVE (in inglese).

Come correggere

Priorità: Bassa — correggere con la manutenzione ordinaria. Motivazione: EPSS 0.2% (percentile 10).

Versioni da aggiornare

  • Linux Linux: vulnerabili le versioni precedenti alla 6.12.118 → aggiornare alla 6.12.118 o successiva.
  • Linux Linux: vulnerabili le versioni precedenti alla 6.18.64 → aggiornare alla 6.18.64 o successiva.
  • Linux Linux: vulnerabili le versioni precedenti alla 7.3.5 → aggiornare alla 7.3.5 o successiva.
  • Linux Linux: versione corretta 6.12.118 (o successiva).
  • Linux Linux: versione corretta 6.18.64 (o successiva).
  • Linux Linux: versione corretta 7.3.5 (o successiva).
  • Linux Linux: versione corretta 7.4-rc1 (o successiva).

Mitigazioni temporanee

Da applicare solo se non è possibile aggiornare subito:

  • Ridurre l'esposizione del componente vulnerabile (segmentazione, accesso solo da reti fidate) finché la patch non è applicata.

Verifica

  1. Individuare tutti gli asset con il prodotto interessato (inventario, scanner di vulnerabilità, CMDB).
  2. Confrontare la versione installata con quelle indicate sopra.
  3. Applicare l'aggiornamento in un ambiente di test, poi in produzione; riavviare i servizi se richiesto.
  4. Ripetere la scansione per confermare la correzione.

Configurazioni interessate

VendorProdottoVersioni vulnerabiliCorretta in
Linux Linux < 6.12.118 6.12.118
Linux Linux < 6.18.64 6.18.64
Linux Linux < 7.3.5 7.3.5
Linux Linux — 6.12.118
Linux Linux — 6.18.64
Linux Linux — 7.3.5
Linux Linux — 7.4-rc1

Riferimenti